Updated specs are available.
Automatic transmission range switch shaft nut (NB1)
This spec doesn't apply to the car you selected.
Not yet checked against the factory manual for your car's year. It's verified in the 1999 Mazda MX-5 Miata Workshop Manual; later manuals may differ.
27–43 in·lb in·lb3–4.9 N·m3–4.9 N·m27–43 in·lb in·lb
Factory manualTaken from a Mazda factory workshop manual, with page citation.
Procedure
Install new packing and lock washer. Tighten nut, then bend lock-washer claws.
Applies to
- NB 1999–2000 (BP-4W, 4AT) — 2000 applicability inferred from 1999 factory evidence within the owner-approved NB1 group.
- Verified in: 1999 Mazda MX-5 Miata Workshop Manual
Sources
- Page 05–13–1327–43 in·lb (3–4.9 N·m)Printed: “3.0–4.9 N·m {30–50 kgf·cm, 27–43 in·lbf}”
Also in Additional NB1 automatic service fasteners
- Hood hinge mounting bolts (NB1)
- Trunk lid hinge to body bolts (NB1)
- Door checker mounting bolts (NB1)
- Door glass stopper bolts (NB1)
- Front door glass guide bolts (NB1)
- Seat mounting bolts (NB1)
- Seat recliner knuckle bolts (NB1)
- Hood release lever bolt (NB1)
- Trunk lid lock bolts (NB1)
- Trunk key cylinder nuts (NB1)
- Soft top windshield-header striker mounting screws (NB1)
- Dashboard upper and side mounting bolts (NB1)
- Dashboard lower mounting bolts (NB1)
- Front bumper upper mounting bolts (NB1)
- Front bumper side mounting fastener — 1.0–1.4 N·m callout (NB1)
- Rear bumper reinforcement mounting nuts (NB1)
- Door weatherstrip screw (NB1)
- Door inner handle screw (NB1)
- Door lock mounting screws (NB1)
- Power window regulator motor screws (NB1)
- Window regulator forward mounting nut — manual and power (NB1)
- Hardtop top lock screws (NB1)
- Hardtop side lock mounting bolts (NB1)
- Hardtop striker mounting bolts (NB1)
- Hardtop rear deck plate bolts (NB1)
- Power antenna mast mounting nut (NB1)
- Accelerator cable bracket bolts (NB1)
- Dynamic chamber bracket bolts (NB1)
- EGR pipe flange bolts at dynamic chamber (NB1)
- Intake air hose clamps (NB1)
- Air cleaner mounting nuts (NB1)
- Fresh-air duct mounting bolt (NB1)
- Mass air flow sensor mounting bolts (NB1)
- Dynamic chamber stay bolts — dynamic chamber side (NB1)
- Dynamic chamber stay bolt — intake manifold side (NB1)
- Fuel distributor bracket bolt (NB1)
- Pulsation damper No. 2 nuts (NB1)
- Pulsation damper No. 1 mounting bolt (NB1)
- Fuel tank service hole cover bolts (NB1)
- Fuel tank insulator mounting nuts (NB1)
- Charcoal canister mounting nuts (NB1)
- Fuel filler pipe upper mounting bolts (NB1)
- Fuel filler pipe lower mounting bolts (NB1)
- Fuel pipe dust cover bolts (NB1)
- Blower unit mounting bolt and nuts (NB1)
- A/C cooling unit mounting nuts (NB1)
- Heater unit mounting nuts (NB1)
- A/C cooling unit inlet pipe fitting (NB1)
- A/C cooling unit outlet pipe fitting (NB1)
- A/C expansion valve inlet fitting (NB1)
- A/C expansion valve to evaporator fitting (NB1)
- A/C condenser mounting bolts (NB1)
- A/C receiver/drier bracket nut (NB1)
- A/C receiver/drier inlet and outlet fittings (NB1)
- A/C condenser inlet fitting (NB1)
- A/C magnetic clutch pressure plate bolt (NB1)
- A/C refrigerant pressure switch (NB1)
- Compressor oil supplement — new cooling unit (NB1)
- Compressor oil supplement — new evaporator (NB1)
- Compressor oil supplement — new condenser (NB1)
- Compressor oil supplement — new receiver/drier (NB1)
- Compressor oil supplement — new cooler hose or pipe (NB1)
- A/C magnetic clutch standard clearance (NB1)
- A/C refrigerant charge (NB1)
- Automatic transmission range switch mounting bolt (NB1)
- Automatic input/turbine speed sensor (NB1)
- Automatic output speed sensor (NB1)
- Automatic shift solenoid A and B mounting bolts (NB1)
- Automatic torque converter clutch solenoid bolt (NB1)
- Automatic transmission control module mounting fasteners (NB1)
- Automatic key interlock solenoid screws (NB1)
- Automatic selector indicator panel screws (NB1)
- Automatic shift-lock actuator mounting fasteners (NB1)