Updated specs are available.
Front bumper side mounting fastener — 1.0–1.4 N·m callout (NB1)
This spec doesn't apply to the car you selected.
Not yet checked against the factory manual for your car's year. It's verified in the 1999 Mazda MX-5 Miata Workshop Manual; later manuals may differ.
9–13 in·lb in·lb1–1.4 N·m1–1.4 N·m9–13 in·lb in·lb
Factory manualTaken from a Mazda factory workshop manual, with page citation.
Procedure
Side mounting fastener identified by the 1.0–1.4 N·m leader; this does not assign torque to lower clips.
Applies to
- NB 1999–2000 (BP-4W) — 2000 applicability inferred from 1999 factory evidence within the owner-approved NB1 year group.
- Verified in: 1999 Mazda MX-5 Miata Workshop Manual
Sources
- Page 09–10–59–13 in·lb (1–1.4 N·m)Printed: “1.0—1.4 N·m {10—15 kgf·cm, 8.7—13.0 in·lbf}”
Also in Additional 1999 factory specifications
- Hood hinge mounting bolts (NB1)
- Trunk lid hinge to body bolts (NB1)
- Door checker mounting bolts (NB1)
- Door glass stopper bolts (NB1)
- Front door glass guide bolts (NB1)
- Seat mounting bolts (NB1)
- Seat recliner knuckle bolts (NB1)
- Hood release lever bolt (NB1)
- Trunk lid lock bolts (NB1)
- Trunk key cylinder nuts (NB1)
- Soft top windshield-header striker mounting screws (NB1)
- Dashboard upper and side mounting bolts (NB1)
- Dashboard lower mounting bolts (NB1)
- Front bumper upper mounting bolts (NB1)
- Rear bumper reinforcement mounting nuts (NB1)
- Door weatherstrip screw (NB1)
- Door inner handle screw (NB1)
- Door lock mounting screws (NB1)
- Power window regulator motor screws (NB1)
- Window regulator forward mounting nut — manual and power (NB1)
- Hardtop top lock screws (NB1)
- Hardtop side lock mounting bolts (NB1)
- Hardtop striker mounting bolts (NB1)
- Hardtop rear deck plate bolts (NB1)
- Power antenna mast mounting nut (NB1)
- Accelerator cable bracket bolts (NB1)
- Dynamic chamber bracket bolts (NB1)
- EGR pipe flange bolts at dynamic chamber (NB1)
- Intake air hose clamps (NB1)
- Air cleaner mounting nuts (NB1)
- Fresh-air duct mounting bolt (NB1)
- Mass air flow sensor mounting bolts (NB1)
- Dynamic chamber stay bolts — dynamic chamber side (NB1)
- Dynamic chamber stay bolt — intake manifold side (NB1)
- Fuel distributor bracket bolt (NB1)
- Pulsation damper No. 2 nuts (NB1)
- Pulsation damper No. 1 mounting bolt (NB1)
- Fuel tank service hole cover bolts (NB1)
- Fuel tank insulator mounting nuts (NB1)
- Charcoal canister mounting nuts (NB1)
- Fuel filler pipe upper mounting bolts (NB1)
- Fuel filler pipe lower mounting bolts (NB1)
- Fuel pipe dust cover bolts (NB1)
- Blower unit mounting bolt and nuts (NB1)
- A/C cooling unit mounting nuts (NB1)
- Heater unit mounting nuts (NB1)
- A/C cooling unit inlet pipe fitting (NB1)
- A/C cooling unit outlet pipe fitting (NB1)
- A/C expansion valve inlet fitting (NB1)
- A/C expansion valve to evaporator fitting (NB1)
- A/C condenser mounting bolts (NB1)
- A/C receiver/drier bracket nut (NB1)
- A/C receiver/drier inlet and outlet fittings (NB1)
- A/C condenser inlet fitting (NB1)
- A/C magnetic clutch pressure plate bolt (NB1)
- A/C refrigerant pressure switch (NB1)
- Compressor oil supplement — new cooling unit (NB1)
- Compressor oil supplement — new evaporator (NB1)
- Compressor oil supplement — new condenser (NB1)
- Compressor oil supplement — new receiver/drier (NB1)
- Compressor oil supplement — new cooler hose or pipe (NB1)
- A/C magnetic clutch standard clearance (NB1)
- A/C refrigerant charge (NB1)
- Automatic transmission range switch shaft nut (NB1)
- Automatic transmission range switch mounting bolt (NB1)
- Automatic input/turbine speed sensor (NB1)
- Automatic output speed sensor (NB1)
- Automatic shift solenoid A and B mounting bolts (NB1)
- Automatic torque converter clutch solenoid bolt (NB1)
- Automatic transmission control module mounting fasteners (NB1)
- Automatic key interlock solenoid screws (NB1)
- Automatic selector indicator panel screws (NB1)
- Automatic shift-lock actuator mounting fasteners (NB1)